Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in San Clemente, CA
Gate installation in San Clemente is rarely a simple swap. The mix of 1940s beach bungalows near the pier, Spanish-style stucco homes along the canyon ridges, and newer gated estates in 92673 means almost every job starts with a conversation about what the driveway can actually support. Salt air off the Pacific eats unprotected steel. Steep driveways off Avenida Presidio and the bluff-top streets above T-Street often rule out a standard sliding track. We plan around that from the first measurement, not after the concrete is poured. If you’re weighing a new gate or a full replacement, call (866) 371-3309 for a site walk and a written price.
Why San Clemente Homes Are Different
San Clemente is a coastal Spanish-revival town where nearly every property meets the street through a driveway or courtyard gate. The constant onshore marine air, salt spray, morning fog, and year-round damp rusts and seizes wrought-iron and steel gates far faster than anything inland Orange County deals with. We replace hinge pins on beach-adjacent homes that have corroded to powder in under a decade. We pull slide rollers out of tracks packed with grit from Santa Ana wind events. And we see control boards on ocean-facing operators that look fine outside but are green with oxidation inside the housing.
The housing stock splits the work in two directions. Older bungalows and 1950s-70s stucco homes near downtown and the pier often have vintage wrought-iron pedestrian gates and swing driveway gates that were never built for automation. Newer hilltop tracts in 92673 and the canyon-edge streets above the pier tend toward sliding gates on steep grades, where a level track isn’t physically possible. The marine layer works on everything, every day. A gate that survives fine in Mission Viejo fails in San Clemente because the air itself is abrasive. We quote and agree on the price before any work starts, so you’re not surprised by what the salt has done to the frame.
Styles & brands we work with
Our Main San Clemente Services
Most San Clemente homeowners call us about one of two things: a gate that won’t move, or a gate that stopped moving safely. Both are covered below, each with its own San Clemente page.
Gate Repair in San Clemente
A bent hinge, a sagging leaf, a bottom rail rotted through from hillside runoff, salt corrosion on the latch, or a weld that let go under repeated wind load. This is everyday work in San Clemente. We straighten or rebuild the frame, replace hardware with marine-grade parts where the exposure calls for it, and reset the swing so the gate closes square instead of dragging across the concrete. The full breakdown of what’s fixable, what’s replaceable, and what it costs is on the dedicated page below. Gate Repair in San Clemente.
Electric Gate Repair in San Clemente
When an automated gate won’t respond, the fault is usually in the board, the safety loop, the motor, or the wiring, and on a salt-exposed San Clemente property it’s often two of those at once. We trace the circuit before we start swapping parts. Coastal moisture gets into limit switches and loop detectors in ways that look like a dead motor but aren’t. We diagnose the actual cause, replace only what’s failed, and recalibrate the operator for the gate’s real weight and travel. Details, brands, and pricing live on this page: Electric Gate Repair in San Clemente.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Gate Installation in San Clemente
Gate installation in San Clemente usually means working with what the property gives you: a short steep driveway in 92673, a salt-facing courtyard off Avenida del Mar, or a bluff-top approach where runoff has been eating the lower rail for decades. We build for that. A new gate here should be spec’d for marine exposure and for the actual grade of the driveway, which is why we measure in person, quote the frame, hardware, operator, and safety edges up front, and confirm the number before any work starts. The full scope of what we install is covered on our Gate Installation page.
Automatic Gate Installation
Signs you need it
You’re opening and closing a heavy gate by hand every day, or the gate was never automated and the driveway now gets more use than it used to.
What it costs in San Clemente
A full automatic gate installation typically ranges from $4,500 to $9,800 depending on gate size, operator type, and whether we’re also running power to the post.
How we do it
We measure the gate leaf and hinge load, choose the right swing or slide operator for the actual weight and wind exposure, mount and wire the motor, install safety loops at the driveway, set the travel limits, and test the full cycle under load.
Driveway Gate Installation
Signs you need it
The old gate has structural rot at the bottom rail, the hinges are pulling out of the post, or the driveway is being widened and the old gate no longer spans the opening.
What it costs in San Clemente
A new fabricated driveway gate, including posts, hinges, and installation, generally runs $3,500 to $8,000 in San Clemente, with steel and aluminum at different price points.
How we do it
We remove the old leaf, set new posts in concrete at the correct depth for the soil, hang the new gate on adjustable hinges, tune the reveal and latch, and add a rust-preventive finish suited to the coastal exposure.
Sliding Gate Installation
Signs you need it
The driveway is too steep or too short for a swing gate, or you need to secure a wider commercial or multi-unit entry without losing parking space to the gate’s arc.
What it costs in San Clemente
Sliding gate installation in San Clemente typically falls between $4,000 and $9,500, with cantilevered hardware on steep grades adding to the frame cost.
How we do it
We check the run and grade first, because many San Clemente hillside driveways can’t take a level track, then set the base, install the track or cantilever rollers, hang the panel, set the end stops, and wire the operator if automation is included.
What Gate Installation Costs in San Clemente
| Item | Typical range in San Clemente |
|---|---|
| Manual driveway gate, installed | $3,500 – $8,000 |
| Automatic gate with operator and safety edges | $4,500 – $9,800 |
| Sliding gate with hardware and automation | $4,000 – $9,500 |
Salt exposure pushes San Clemente prices toward the upper end when we need stainless hinges, sealed control enclosures, or a cantilevered slide because the driveway can’t support a level track. The quote you approve is the price you pay, no change orders slipped in after the concrete cures.
Do you handle the power run and the safety edges on an automatic gate?
Yes. We run the low-voltage conduit and wiring from the house or nearest power source to the operator post, and we install the safety loops or photo eyes required to keep the gate from closing on a car or a person. The full electrical run is included in our quote before work begins.
How long does a full gate installation take in San Clemente?
Most residential installations take one to two days once the posts are set and the concrete has cured. Custom cantilevered slides or long power runs on hillside lots can add a day. We schedule the work around the cure time so you’re not waiting on a gate that’s hung but not bedded.
Brands We Service in San Clemente
We work on FAAC, BFT, Linear, and Viking operators, along with the full residential and commercial range. For a third of the boards we open in San Clemente, the fix is a corroded relay or a salt-damaged limit switch, not a dead motor. We carry the common relays, capacitors, and edge sensors for those brands in our service stock, so most repairs are done in one visit. Our brands page lists every operator we support.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in San Clemente, CA
| Service | Typical range in San Clemente |
|---|---|
| Hinge or hardware replacement | $180 – $450 |
| Weld repair to frame or leaf | $250 – $700 |
| Gate not closing properly, realign and adjust | $180 – $400 |
| Operator replacement (motor and arm) | $900 – $2,800 |
| Control board replacement | $400 – $1,100 |
| Loop detector or safety edge replacement | $350 – $800 |
| Manual gate installation, full new gate | $3,500 – $8,000 |
| Automatic gate installation with operator | $4,500 – $9,800 |
| Sliding gate installation with hardware | $4,000 – $9,500 |
What pushes a San Clemente repair or install higher is almost always the salt. Marine-grade stainless hardware, sealed operator enclosures, and cantilevered slide systems for steep driveways all add material cost. We quote the job before we start, and we don’t send an invoice that doesn’t match the number you already approved.
Neighborhoods We Serve in San Clemente
We cover all of San Clemente, from the pier and downtown to the hills above the coast. Most calls in 92672 and 92674 we can reach within the same day. The hilltop streets in 92673 are usually next-day, simply because the drive up takes a little longer.
- Pier Bowl and downtown
- North Beach and Avenida Del Mar
- T-Street and the bluff-top streets above it
- Talega and the 92673 hilltop tracts
- Forster Ranch and the canyon-edge streets
Service Area – Cities Near San Clemente
When a gate job takes us outside San Clemente, we often head north into Laguna Beach, CA or Laguna Hills, CA for similar coastal corrosion work, inland to Ladera Ranch, CA where the gates are newer but the operators get heavy daily cycling, and up into Coto De Caza, CA for larger estate and equestrian-property gates. Same diagnostic approach, same upfront pricing.
Serving San Clemente, CA — Our Local Coverage Area
We’re based in the San Clemente area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Company in San Clemente
In most San Clemente residential cases, replacing the gate itself doesn’t require a permit, but adding a new electrical run for an operator often does. If your HOA is involved, they’ll want to see the design before installation. We handle the measurements and can flag what your HOA or the city is likely to require before you commit.
For a security issue where the gate is stuck open or parked across the driveway, call us as early in the day as you can. We reserve same-day slots for exactly that, and we’ll tell you honestly on the phone whether we can make it before evening or whether tomorrow morning is the realistic window.
Bring us the HOA’s spec sheet or the management company’s contact, and we’ll build or repair to match it. San Clemente HOAs, especially in the newer 92673 tracts, often mandate specific gate heights, colors, and even operator noise levels. We’ve worked to those specs often enough that they rarely slow the job down.
If your gate is damaged, stuck, or simply past saving, call (866) 371-3309 and we’ll walk the site with you, measure what’s there, and put a firm number in writing. Montclair Gate Repair has served San Clemente since 2013.
What happens when you call
- 1A real person answersNo phone trees — talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you — the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What San Clemente Customers Say
"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
— Emily Park"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
— Alejandro Herrera"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
— Amanda Padgett