Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across Fontana
Electric gate repair in Fontana typically runs $180 – $340 for most board, hinge, and motor issues on residential swing gates, and we usually have a technician in your neighborhood the same day you call. If your gate is stuck half-open on Sierra Avenue or throwing a fault code in a Southridge subdivision, that’s a security gap, not just a driveway annoyance. We work on your brand, we trace the fault to the actual cause, and we fix it correctly the first trip. Call (866) 371-3309 for a free estimate.
Key Takeaways
- Electric gate repair in Fontana costs $180 – $340 for common residential fixes, with commercial slide-gate work running higher depending on the operator.
- We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Nine brands, one call.
- Fontana’s older 92335 core has a specific failure pattern: obsolete boards, rotted hinge posts, and sagging gates that drag on the drive.
- The retrofit-versus-replace decision is the most important call we help Fontana homeowners make, and we’ll tell you straight which one saves money.
Styles & brands we work with
Why Montclair Gate Repair Is Fontana’s Preferred Electric Gate Repair Company
Most of our Fontana calls are not simple “motor stopped working” jobs. They’re 1950s-to-1970s tract homes in the 92335 core with gates that have been hanging in dry heat and Santa Ana wind for 50 years, and the failure is rarely one thing. It’s a control board that’s been obsolete for a decade, a hinge post rotted at the footing, and a panel that’s warped enough to trip the operator before it reaches full travel. A general handyman will replace the cheapest part and leave the other two problems in place. We don’t do that.
We carry diagnostic equipment for control boards, safety loops, and motor circuits, and our techs work across nine operator brands so you’re not bounced between a “residential guy” and a “commercial guy” depending on what’s bolted to your gate. In Fontana, that matters because the same neighborhood can have a Mighty Mule on a side yard gate, a DoorKing on a warehouse slide gate off Valley Boulevard, and a 1970s FAAC on a legacy swing gate that has not had parts available for a decade. One company covers all of it. Noel Carrasco has built the team around that specific range.
Automatic Gate Repair in Fontana
Automatic gate repair in Fontana usually means a swing gate operator that has stopped responding, failed to open fully, or started reversing mid-cycle, and the fix typically runs $200 – $340 on residential systems. The first thing we check is whether the problem is the operator at all. On Fontana’s older gates, we see a lot of operators throwing fault codes because the gate itself has sagged or warped, and the motor is burning itself out against a panel that no longer swings true. In that case the repair might be a hinge and post correction with a board reset, not a motor replacement.
Legacy Systems and Retrofits
If you have a 1960s or 1970s automatic swing gate in Fontana with an old FAAC, BFT, or Linear operator, the question is not “can you fix it” but “can you still get the parts.” Some boards for these legacy units are simply gone from the supply chain. When we can retrofit a modern operator onto the existing ironwork and keep your gate, we do that. When the post is rotted and the board is obsolete and the motor is 30 years old, replacement is the cheaper answer and we’ll tell you that directly.
Safety Loop and Photocell Repairs
Automatic gates in Fontana are required to stop and reverse on obstruction, which means the safety photocells and vehicle detection loops have to work. A gate that starts closing on a car or a kid because the loops are dead or the photo-eyes are misaligned is not just a nuisance, it’s a hazard. We test and replace these as part of the repair, and on older gates in 92335 we often find the loops were never installed correctly in the first place.
Electric Gate Motor in Fontana
Electric gate motor replacement in Fontana runs $350 – $800 for most residential swing gate operators, depending on the brand and whether the arm, chain, or gear drive needs to be matched. A motor that just hums and doesn’t move, or one that runs but won’t open the gate fully, is either a capacitor failure or a mechanical bind, and we diagnose it before we quote it. On Fontana’s older gates, we sometimes find the motor is fine and the problem is actually a warped wood panel or a sagging hinge dragging the gate against the driveway enough to overload the motor every cycle.
Matching Motor to Gate
When the motor does need replacing, we match it to the gate’s weight and cycle use, not just the brand sticker on the old unit. A heavy ornamental iron gate on a double driveway in the 92337 new subdivisions needs a different motor than a lightweight chain-link side gate in a 92335 mid-century home. We stock or order parts across LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so we’re not steering you toward whatever happens to be on the truck.
Trusted Brands We Service in Fontana
We work on your brand, whichever one is on the housing. That means LiftMaster and Mighty Mule on residential gates, DoorKing and Elite on commercial slide and swing operators in Fontana’s warehouse corridor, and the older FAAC and BFT units still hanging on mid-century gates in 92335. Nine brands, one call. For Fontana customers we keep common residential parts stocked locally, so a board swap or a sensor replacement does not wait on a two-week order. If you know the brand on your gate, tell us when you call. If you don’t, we’ll identify it on arrival.
See the difference
Before
After
Before
After
Before
AfterCommon Electric Gate Repair Problems We See in Fontana Homes
- Obsolete FAAC, BFT, and Linear boards on 1950s – ’70s gates. Fontana’s 92335 core has a lot of legacy operators that were installed when the homes were built. Replacement boards for many of those units are no longer manufactured, so the repair call becomes a retrofit call.
- Rotted or heaved hinge posts at the footing. Decades of dry heat, Santa Ana wind load, and a few winter rains corrode the post right where it enters the concrete. The gate starts to drag, the operator trips on overload, and the post eventually fails.
- Warped wood panels on older side-yard and drive gates. Fontana’s dry inland air pulls moisture out of wood, and the summer heat plus wind cycles will bow a panel enough that it no longer clears the drive. The operator works, the gate doesn’t, and the motor eats itself trying to finish the cycle.
- Failed safety loops and photo-eyes on commercial gates along the I-10 corridor. Fontana’s warehouse and truck-yard gates see heavy daily cycle use and constant vehicle traffic over loop detectors. When the loops fail, the gate loses its obstruction safety, and when the photo-eyes go out of alignment, the gate will refuse to close.
Pricing for Electric Gate Repair in Fontana, CA
Here’s straight numbers for the Fontana market. Basic swing gate motor repairs and board replacements run $180 – $340. A full electric gate motor replacement on a residential driveway gate runs $350 – $800. A complete retrofit, where we pull an obsolete operator off a legacy gate and install a new one with working safety photocells, typically lands $700 – $1,200 depending on whether we also have to re-hang the gate or replace a post. Commercial slide gate operator work in Fontana’s warehouse zone can run higher based on operator duty cycle and gate weight above any of these ranges. Every job is quoted and agreed before any work starts, so the number we give you is the number you pay. Call (866) 371-3309 for a free estimate.
We Also Serve Cities Near Fontana
From Fontana we work outward through Electric Gate Repair in Fontana and into Bloomington, Rialto, Glen Avon, and Pedley. Same tech, same brand coverage, same retrofit knowledge. If your gate is in one of those cities, call the same number and mention the city. We’ll route to whoever has the right parts on the truck that day. Our Electric Gate Repair team covers the whole Inland Empire corridor.
Serving Fontana, CA — Our Local Coverage Area
We’re based in the Fontana area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Fontana
Yes, in most cases we can retrofit the existing gate and keep your original ironwork, but the operator itself often gets replaced because the old control board is obsolete and no longer available. We swap in a modern LiftMaster or FAAC unit, wire in safety photocells and loops that meet current code, and the gate keeps its original look. If the post is rotted or the gate is too far gone, we’ll tell you replacement is cheaper than piling parts into a failing frame.
It’s almost always the gate. Fontana’s dry heat and Santa Ana winds pull moisture out of wood until panels bow and hinges loosen, and then the warped gate drags on the concrete and trips the operator before it finishes the cycle. We correct the gate or re-hang it before we blame the motor. Sometimes the fix is a hinge and post correction with the existing operator. Sometimes the panel has to be rebuilt. Call (866) 371-3309 and we’ll tell you which one you have.
Yes. Automatic gates in California are required to have an external entrapment protection system, which means functional safety photocells and working obstruction detection, whether the gate is a 1950s original or a new install. If your older Fontana gate was installed before these requirements existed, it likely does not meet current safety standards, and we can add photocells and loops during a retrofit so the gate is lawful and safe.
A failing hinge post shows rust at the ground line, visible leaning, or concrete cracking around the footing, and on Fontana’s 1950s – ’70s gates we see it constantly because decades of sun, wind, and occasional winter rain work the post where it enters the concrete. When the post moves, the gate sags, the panel drags, and the operator overloads trying to complete every cycle. Ignoring it eventually means the post fails completely and the gate falls. We can sink a new post, correct the sag, and save the gate.
Santa Ana winds slam slide gates against their end-stops and v-guides, which loosens hardware and knocks limit switches out of adjustment, while summer heat stress on operators running dozens of cycles a day shortens motor and capacitor life. Truck yard slide gates in Fontana also take constant abuse from vehicle loops and photo-eyes getting hit by trucks and trailers. We see more failed safety loops and misaligned photo-eyes on I-10 corridor slide gates than anything else. Call (866) 371-3309 for an exact quote; estimates are free.
Call Montclair Gate Repair for Electric Gate Repair in Fontana, CA
If your gate is stuck, sagging, or throwing a fault code in Fontana, the number is (866) 371-3309. We’ll ask what brand you have, what the gate is doing, and whether it’s a 92335 mid-century swing gate or a commercial slide gate on the warehouse side of town. Then we’ll tell you straight whether it’s a retrofit or a replace, and the price is set before any work starts. Nine brands, one call, and a technician who knows your specific gate. Free estimates, upfront pricing, and work done right the first trip.
Written by Noel Carrasco, Owner at Montclair Gate Repair, serving Fontana and the Inland Empire with electric gate repair and installation.